Integrated Brushless Servo Motor with Driver Built-in System

Integrated Brushless Servo Motor with Driver Built-in System

 Integrated Brushless Servo Motor with Driver Developed-in Technique

57IV90/57IV130/57IV180 Functions
1.Operating voltage: DC input voltage 15VDC to 50VDC ,advise voltage is 36V
two.The max constant output current is 10A, the max peak recent is 22A (3 moments overload potential) 
three.Acceptable differential or solitary-finished pulse / path command, have 3 control method of position, velocity and torqe
four.Using FOC magnetic placement manage technology and space vector pulse width modulation (SVPWM) closed-loop manage technological innovation
five.The quantity of pulses for every cycle (subdivision) can be established by the debug application or the dial change location(digital equipment ratio)
6.Have a few varieties of 90w,130w and 180w DC brushless servo motor to choose.
7.Have safety of overvoltage, undervoltage, overcurrent and tolerance,and so forth.
8.Solitary / double pulse mode, the pulse valid edge can be decide on.
9.The max pulse frequency of management instruction is 500KHz (manufacturing facility default is 200KHz)
ten.Pulse, course and allow sign enter interface stage is four.five to 28V suitable
eleven.With serial RS232 / RS485 debugging operate, but want to use our particular serial debugging cable 
twelve.Functionality: clean speed, modest overshoot ,modest tracking error, minimal warmth of motor and driver

Advantage
This servo motor system is produced up of brushless servo motor with driver constructed-in.Compact and little dimension is appropriate for some place that has requirement of volume.It has significantly less wiring to lessen mistakes,keep stable and effortless for set up.This built-in servo system has very good speed adjustment functionality,big starting torque,smooth procedure, substantial rotating speed.The price is a lot lower than AC servo motor, but some performances are greater than AC servo products.

Driver Model And Assortment Xihu (West Lake) Dis.

Motor Type  57IV90 57IV130 57IV180
Rated power(W) 90W 130W 180W
Vector Maximum Current 16A 18A 22A
Body Length(MM) 106.2 0.five 126.2 0.five 146.2 0.5
Operation Voltage fifteen-50Vdc,36Vdc recommend 
Overvoltage Protection Voltage 68Vdc±2
Control Method 32 bits DSP vector FOC control technology
Pulse Limit Frequency 500KHz(factory default 200KHz)
Security Overcurrent, overvoltage, undervoltage and tracking error tolerance alarm
Input Signal  Pulse, direction and enable differential / single-ended interface signal,
interface level 4.five-28Vdc compatible, no need external current limiting resistor
Output Signal  Alarm / in-position signal OC output, the output capacity is100mA, need external
pull-up resistor, the maximum pull up voltage is 24Vdc
Electronic Gear Ratio Default 4000 / rev, through the DIP switch or debug software setting subdivision
(200-51200)
Position Error Control Accuracy ±1 Pulse
Speed Control Accuracy  ±2 rpm
Maximum  Acceleration 100 rpm/ms

Dialing Switch Configurations

Pulse/Rev. SW1 SW2 SW3 SW4
Default ON ON ON ON
800 OFF ON ON ON
1600 ON OFF ON ON
3200 OFF OFF ON ON
6400 ON ON OFF ON
12800 OFF ON OFF ON
25600 ON OFF OFF ON
51200 OFF OFF OFF ON
one thousand ON ON ON OFF
2000 OFF ON ON OFF
4000 ON OFF ON OFF
5000 OFF OFF ON OFF
8000 ON ON OFF OFF
10000 OFF ON OFF OFF
20000 ON OFF OFF OFF
40000 OFF OFF OFF OFF

Subdivision accuracy (electronic equipment ratio) :When SW1, SW2, SW3, SW4 are ON, the push utilizes the inside default micro-phase subdivision, the default interior subdivision of the driver is 400Pulse / rev, and the electronic equipment ratio can also be set by the debugging software program. SW5 established the motor route,when turnON, the motor turns clockwise (CW),when turn OFF, the motor turns counterclockwise(CCW). SW6 management mode variety, whenON, the motor enters the self-take a look at method,generating one particular CZPT and reverse revolution, has been repeated until finally exit self-check mode, the exterior management signal is invalid at self check method, whenOFF, the motor exits self-check mode,then the external handle sign is valid.

Mechanical Structure Dimension

 Driver mode Motor body length(mm) Driver thickness(mm) Integrated motor driver length(mm)
57IV90 seventy six 30.2 106.2
57IV130  96 30.two 126.2
57IV180  116 thirty.2 149.2

Observe : All above is typically used, and we can personalize in accordance to your ask for or choose the suitable design for you, you should explain to us adhering to parameters: recent, voltage, keeping torque, physique size,the application location.

Application
Suitable for all sorts of tiny and medium-sized automation equipments and instruments. Such as: laser equipment, health care gear, 3D printer, modest and medium-sized engraving equipment, electronic processing equipment, automatic crawling equipment, specific CNC device instrument, packaging tools and robotic. It is specifically valuable for end users who anticipate lower noise and large speed apps.

Packaging and shipping and delivery
1.Outer packing: CZPT export carton with necessary delivery marks
two.Internal packing: Water-proof packing with shock absorbing EPE and cardboard surrounded 
three.As for every the clients requirements

Our provider
1.Operating time : 8:00 a.m – 10:00 p.m .Any inquiries, make sure you tell us freely, we will be reply you asap.
two.Lead time : For samples, two to 5 days will be Ok. For mass generation, the lead time count on the quantities you need to have.
3.Warrantity period of time : 18 months and Existence-long routine maintenance support for the product.
four.We acknowledge items customize.

FAQ
Q1: How to decide on the ideal stepper or servo motor?
A1: There are serveral essential objects: measurement, duration, holding torque, voltage, recent etc.Right after confirm them and informed us, we can choose the ideal a single for you.

Q2: Any other strategies to finalize the product?
A2: Sure, you can send out us the model you are employing, we can support you locate the suitable one.

Q3:How to promise the Good quality of CZPT Areas?
A3: We have the built-in technique for industrial parts quality control. We have IQC (incoming quality control), IPQCS (in process quality management section), FQC (last high quality handle) and OQC (out-going quality management) to control each and every procedure of industrial areas prodution.

This fall:What is the Gain of Your Components for Market Merchandise? 
A4:1.The gain of our items is the aggressive costs, rapidly shipping and delivery and substantial top quality. Our
employees are dependable-oriented, friendly-oriented,and diligent-oriented. Our items are featured by strict tolerance, sleek complete and extended provider time.
2.Prior to we send out the items,we check them a lot more than 3 instances.

Speak to

 

Integrated Brushless Servo Motor with Driver Built-in System